Unterschiede

Hier werden die Unterschiede zwischen zwei Versionen der Seite angezeigt.

--- hardware:boards [2023/01/10 17:00] – ↷ Links angepasst weil Seiten im Wiki verschoben wurden kst
+++ hardware:boards [2023/01/10 17:11] (aktuell) – gelöscht kst
@@ Zeile 1: / Zeile 1: @@
-====== Boards ======
-  * MKS Gen L
-  * Bigtreetech SKR E3 1.4 Turbo
-===== Creality 1.1.3 =====
-{{:hardware:creality_1.1.3:pxl_20230110_125358399.jpg?400|}}\\
-{{:hardware:creality_1.1.3:pxl_20230110_125351473.jpg?400|}}
-===== Creality 1.1.4 =====
-Dies waren die ersten Boards von Creality mit TMC Treibern, sie wurden als "Silent Board" verkauft. Es gab jedoch auch 1.1.4 die die alten Treiber hatten und so als OEM kamen. Man kann es leider nicht von außen feststellen.
-Die TMCs werden im Standalone-Modus gefahren.
-===== Creality 4.2.2 =====
-{{hardware:creality_4.2.2:pxl_20221222_232605145.jpg?400|}}\\
-{{hardware:creality_4.2.2:pxl_20221222_235012330.jpg?400|}}
-===== RAMPS 1.4 =====
-  * https://3dprint.wiki/reprap/electronics/ramps
-  * https://www.geeetech.com/wiki/index.php/Ramps1.4
-  * https://www.youtube.com/watch?v=pWdm_KwDvd4
-  * https://de.aliexpress.com/item/1005002011277357.html
-{{:hardware:ramps:pxl_20230110_124705078.jpg?400|}}\\
-{{:hardware:ramps:pxl_20230110_124711160.jpg?400|}}\\
-{{:hardware:ramps:pxl_20230110_124715936.jpg?400|}}\\
-{{:hardware:ramps:pxl_20230110_124727384.jpg?400|}}\\
-{{:hardware:ramps:pxl_20230110_124821911.jpg?400|}}\\
-{{:hardware:ramps:pxl_20230110_124831578.jpg?400|}}\\
-{{:hardware:ramps:pxl_20230110_124952065.jpg?400|}}
-===== Bigtreetech SKR Pico =====
-  * Das Board hat einen RPi Pico Core mit TMC2209 Treibern im Uart Modus.
-  * Es hat die Abmessungen eines RPi und würde prima mit einem RPi 3, 4 oder Zero 2 zusammen passen.
-  * Marlin: https://github.com/thinkyhead/Marlin/tree/bf2_wip_rp2040_skr_pico_PR
-  * Benötigt bei Entnahme von mehr als 0,9A pro Treiber aktive Kühlung.
-{{:hardware:btt_skr_pico:pxl_20230110_122823532.jpg?400|}}\\
-{{:hardware:btt_skr_pico:pxl_20230110_122953053.jpg?400|}}\\
-{{:hardware:btt_skr_pico:pxl_20230110_123013351.jpg?400|}}\\
-{{:hardware:btt_skr_pico:pxl_20230110_123029740.jpg?400|}}\\
-{{:hardware:btt_skr_pico:pxl_20230110_123052010.jpg?400|}}\\
-{{:hardware:btt_skr_pico:pxl_20230110_123143301.jpg?400|}}\\
-{{:hardware:btt_skr_pico:pxl_20230110_123308783.jpg?400|}}
-==== Klipper Konfiguration für Ender 3 mit BL-Touch ====
-<code>
-[include fluidd.cfg]
-#[include adxl.cfg]
-[include kiauh_macros.cfg]
-[include macros.cfg]
-[include start_end_macros.cfg]
-[mcu]
-serial: /dev/serial/by-id/usb-Klipper_rp2040_3672894954322E18-if00
-[printer]
-kinematics: cartesian
-max_velocity: 300
-max_accel: 3000
-max_accel_to_decel: 1500
-max_z_velocity: 5
-square_corner_velocity: 5
-max_z_accel: 100
-[input_shaper]
-shaper_freq_x: 98.8
-shaper_type_x: mzv
-shaper_freq_y: 40.8
-shaper_type_y: mzv
-[gcode_arcs]
-[stepper_x]
-step_pin: gpio11
-dir_pin: !gpio10
-enable_pin: !gpio12
-microsteps: 16
-full_steps_per_rotation: 200
-rotation_distance: 40
-endstop_pin: ^gpio4
-# endstop_pin: tmc2209_stepper_x:virtual_endstop
-# homing_retract_dist: 0
-position_endstop: 0
-position_max: 225
-homing_speed: 100
-[tmc2209 stepper_x]
-uart_pin: gpio9
-tx_pin: gpio8
-uart_address: 0
-run_current: 1
-hold_current: 0.7
-stealthchop_threshold: 0
-# diag_pin: ^gpio4
-# driver_SGTHRS: 100
-[stepper_y]
-step_pin: gpio6
-dir_pin: !gpio5
-enable_pin: !gpio7
-microsteps: 16
-full_steps_per_rotation: 200
-rotation_distance: 40
-endstop_pin: ^gpio3
-# endstop_pin: tmc2209_stepper_y:virtual_endstop
-# homing_retract_dist: 0
-position_endstop: 0
-position_max: 225
-homing_speed: 100
-[tmc2209 stepper_y]
-uart_pin: gpio9
-tx_pin: gpio8
-uart_address: 2
-run_current: 0.75
-hold_current: 0.5
-stealthchop_threshold: 0
-diag_pin: ^gpio3
-driver_SGTHRS: 100
-[stepper_z]
-step_pin: gpio19
-dir_pin: gpio28
-enable_pin: !gpio2
-microsteps: 16
-full_steps_per_rotation: 200
-rotation_distance: 8
-# endstop_pin: ^gpio25
-endstop_pin:probe: z_virtual_endstop
-position_min: -5
-position_max: 255
-homing_speed: 35
-[tmc2209 stepper_z]
-uart_pin: gpio9
-tx_pin: gpio8
-uart_address: 1
-run_current: 0.7
-hold_current: 0.5
-stealthchop_threshold: 0
-[extruder]
-step_pin: gpio14
-dir_pin: !gpio13
-enable_pin: !gpio15
-microsteps: 16
-rotation_distance: 22.230
-nozzle_diameter: 0.4
-filament_diameter: 1.75
-heater_pin: gpio23
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: gpio27
-control = pid
-pid_kp = 30.959
-pid_ki = 1.433
-pid_kd = 167.179
-min_temp: 0
-max_temp: 250
-min_extrude_temp: 180
-pressure_advance = 0.40
-pressure_advance_smooth_time: 0.040
-[tmc2209 extruder]
-uart_pin: gpio9
-tx_pin: gpio8
-uart_address: 3
-run_current: 0.7
-hold_current: 0.5
-stealthchop_threshold: 0
-# [filament_switch_sensor runout_sensor]
-# switch_pin: ^gpio16
-# pause_on_runout: True
-# [filament_motion_sensor smart_sensor]
-# switch_pin: ^gpio16
-# detection_length: 2.5
-[heater_bed]
-heater_pin: gpio24
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: gpio26
-#control: pid
-#pid_Kp=71.830
-#pid_Ki=1.800
-#pid_Kd=716.505
-min_temp: 0
-max_temp: 110
-[fan]
-pin: gpio17
-[heater_fan hotend_fan]
-pin: gpio18
-heater: extruder
-heater_temp: 50.0
-[safe_z_home]
-home_xy_position: 110, 110 # Change coordinates to the center of your print bed
-speed: 100
-z_hop: 10                 # Move up 10mm
-z_hop_speed: 80
-[bed_screws]
-screw1: 30.5, 37
-screw2: 30.5, 207
-screw3: 204.5, 207
-screw4: 204.5, 37
-screw5: 110, 110
-[bltouch]
-sensor_pin: gpio22
-control_pin: gpio29
-#z_offset: 0.2
-x_offset: -42
-y_offset:0
-samples: 2
-[bed_mesh]
-speed: 150
-horizontal_move_z: 5
-mesh_min: 20, 30
-mesh_max: 170, 210
-probe_count: 5, 3
-[temperature_sensor Board_MCU]
-sensor_type: temperature_mcu
-min_temp: 0
-max_temp: 100
-[temperature_sensor Raspberry_Pi]
-sensor_type: temperature_host
-min_temp: 0
-max_temp: 100
-#[neopixel board_rgb]
-#pin: gpio24
-#chain_count: 1
-#color_order: GRB
-#initial_RED: 0
-#initial_GREEN: 0.5
-#initial_BLUE: 0 # Paste here and save your klipper configuration
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*#
-#*# [bltouch]
-#*# z_offset = 2.050
-#*#
-#*# [bed_mesh Magnet plate]
-#*# version = 1
-#*# points =
-#*#     -0.326250, -0.450000, -0.507500, -0.567500, -0.586250
-#*#     -0.361250, -0.488750, -0.567500, -0.561250, -0.490000
-#*#     -0.351250, -0.462500, -0.497500, -0.502500, -0.466250
-#*# tension = 0.2
-#*# min_x = 20.0
-#*# algo = lagrange
-#*# y_count = 3
-#*# mesh_y_pps = 2
-#*# min_y = 30.0
-#*# x_count = 5
-#*# max_y = 210.0
-#*# mesh_x_pps = 2
-#*# max_x = 170.0
-#*#
-#*# [heater_bed]
-#*# control = pid
-#*# pid_kp = 74.810
-#*# pid_ki = 1.827
-#*# pid_kd = 765.872
-#*#
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*#     -0.012500, -0.151250, -0.202500, -0.211250, -0.173750
-#*#     0.207500, 0.043750, -0.051250, -0.112500, -0.077500
-#*#     0.441250, 0.253750, 0.107500, -0.008750, -0.052500
-#*# tension = 0.2
-#*# min_x = 20.0
-#*# algo = lagrange
-#*# y_count = 3
-#*# mesh_y_pps = 2
-#*# min_y = 30.0
-#*# x_count = 5
-#*# max_y = 210.0
-#*# mesh_x_pps = 2
-#*# max_x = 170.0
-</code>